#
# Zaptel Configuration File
#
# This file is parsed by the Zaptel Configurator, torcfg
#
#
# First come the span definitions, in the format
# span=<span num>,<timing>,<line build out (LBO)>,<framing>,<coding>[,yellow]
# 
# The timing parameter determines the selection of primary, secondary, and
# so on sync sources.  If this span should be considered a primary sync
# source, then give it a value of "1".  For a secondary, use "2", and so on.
# To not use this as a sync source, just use "0"
#
# The line build-out (or LBO) is an integer, from the following table:
# 0: 0 db (CSU) / 0-133 feet (DSX-1)
# 1: 133-266 feet (DSX-1)
# 2: 266-399 feet (DSX-1)
# 3: 399-533 feet (DSX-1)
# 4: 533-655 feet (DSX-1)
# 5: -7.5db (CSU)
# 6: -15db (CSU)
# 7: -22.5db (CSU)
#
# The framing is one of "d4" or "esf"
#
# The coding is one of "ami" or "b8zs"
#
# If the keyword "yellow" follows, yellow alarm is transmitted when no
# channels are open.
#
#span=1,0,0,esf,b8zs
#span=2,1,0,esf,b8zs
#
# Next come the definitions for using the channels.  The format is:
# <device>=<channel list>
#
# Valid devices are:
#
# "e&m"     : Channel(s) are signalled using E&M signalling (specific
#             implementation, such as Immediate, Wink, or Feature Group D
#             are handled by the userspace library).
# "fxsls"   : Channel(s) are signalled using FXS Loopstart protocol.
# "fxsgs"   : Channel(s) are signalled using FXS Groundstart protocol.
# "fxsks"   : Channel(s) are signalled using FXS Koolstart protocol.
# "fxols"   : Channel(s) are signalled using FXO Loopstart protocol.
# "fxogs"   : Channel(s) are signalled using FXO Groundstart protocol.
# "fxoks"   : Channel(s) are signalled using FXO Koolstart protocol.
# "unused"  : No signalling is performed, each channel in the list remains idle
# "clear"   : Channel(s) are bundled into a single span.  No conversion or
#             signalling is performed, and raw data is available on the master.
# "indclear": Like "clear" except all channels are treated individually and
#             are not bundled.  "bchan" is an alias for this.
# "rawhdlc" : The zaptel driver performs HDLC encoding and decoding on the 
#             bundle, and the resulting data is communicated via the master
#             device.
# "fcshdlc" : The zapdel driver performs HDLC encoding and decoding on the
#             bundle and also performs incoming and outgoing FCS insertion
#             and verification.  "dchan" is an alias for this.
# "nethdlc" : The zaptel driver bundles the channels together into an
#             hdlc network device, which in turn can be configured with
#             sethdlc (available separately).
#
# The channel list is a comma-separated list of channels or ranges, for
# example:
#
#   1,3,5 (channels one, three, and five)
#   16-23, 29 (channels 16 through 23, as well as channel 29
#
# So, some complete examples are:
#   e&m=1-12
#   nethdlc=13-24
#   fxsls=25,26,27,28
#   fxols=29-32
#
fxsks=1
#fxsls=1
#fxoks=1-24
#bchan=25-47
#dchan=48
#fxols=1-12
#fxols=13-24
#e&m=25-29
#nethdlc=30-33
#clear=44
#clear=45
#clear=46
#clear=47
#fcshdlc=48
#
# Finally, you can preload some tone zones, to prevent them from getting
# overwritten by other users (if you allow non-root users to open /dev/tor*
# interfaces anyway.  Also this means they won't have to be loaded at runtime.
# The format is "loadzone=<zone>" where the zone is a two letter country code.
# 
# You may also specify a default zone with "defaultzone=<zone>" where zone
# is a two letter country code.
#
loadzone = us
#loadzone=fr
#loadzone=fr
#loadzone=de
#loadzone=uk
defaultzone=us